Vision Fitness T9800 Series User Manual download pdf (Page 3)

Assembly

Guide

To avoid possible damage to this Platform Treadmill, please follow these assembly steps in the correct

order. Before proceeding though, find your new Platform Treadmill’s 2 serial numbers, located on the

underside of the main frame, and on the bottom of the console, and enter here:

Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty

Card and in your own records. Be sure to read your Owner’s Guide before using your new Platform Treadmill.

If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Platform

Treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts

are in place and partially threaded in before completely tightening any ONE bolt.

STEP

• Remove motor cover screws and

take off the motor cover.

• Insert the right console mast to the

right console mast bracket. First, fasten

the inside of the console mast to the

console mast bracket by securing four

bolts (M8x15L socket head) and four

washers (8.2x19x2T). Fully tighten the

bolts. Second, fasten the two bolts

(M10x20L button head) and two

washers (10.2x19x2T) on the front of

the console mast and fully tighten.

• Repeat on the left side

ORANGE BAG

STEP

• Insert the handlebar cover onto the

handlebar. Insert the right handlebar

by holding the handlebar sideways

toward the treadmill and inserting the

top into the console. Rotate the

handlebar into the bracket located on

the console mast. Fasten with a bolt

(M5x12L), and a bolt (M6x15L socket

head) & an arc washer (6.5x13x1T)

into the two holes of the console plas-

tic, and a bolt (M8x15L flat head) into

the hole in the handlebar. Fasten a bolt

(M6x15L socket head) and a flat washer

(6.5x19x2T) into the hole in the handle-

bar on the console mast. Do not fully

tighten the bolts.

• Slide the handlebar cover over the

bracket and secure with a bolt

(M6x15L socket head) and a flat

washer (6.5x19x2T). Do not fully

tighten the bolt.

• Repeat on the left side.

• Fully tighten the console and

handlebar bolts.

PINK BAG

STEP

T9800 Series

TREADMILLS

STEP

• If the running belt slips when used,

run the treadmill at 2.0 mph and use

the supplied 8mm Allen wrench to turn

the left and right tension bolts clockwise

/4-turn at a time until the belt no

longer slips.

• If the running belt is too far to the

right

side, run the treadmill at 2.0 mph

and use the supplied 8mm Allen

wrench to turn the

right

tension bolt

clockwise

/4-turn at a time until the

belt remains centered during use.

If the running belt is too far to the

left

side, run the treadmill at 2.0 mph and

turn the

left

tension bolt clockwise

/4-turn at a time until the belt remains

centered during use.

BELT TENSION

STEP

• Place the motor cover back on the

frame and fasten with 6 screws.

• Attach the power cord to the treadmill.

• Plug the power cord into the power

outlet.

MOTOR COVER

STEP

Frame Serial Number

Console Serial Number

STEP

• Tie the ribbon data cable, TV

power cable, and coaxial cable to

the cable wire tie on the top of the

right console mast. Feed the cables

down the console mast and through the

hole at the lower part of the console

mast. Remove protective plastic cover.

Push any remaining cable into the

console mast.

• Mount the console onto the left and

right console masts using four bolts

(M8x15L socket head) and four washers

(8.2x19x2T). Do not fully tighten.

• Take the wire tie off the cables. Plug

the large 20-pin ribbon connector into

the 20-pin connector on the lower

control board. Attach the two grounding

wire connectors to the two grounding

wires located in the motor pan near

the front of the frame. Connect the TV

power cable to the TV power connector

and coaxial cable to the coaxial

cable connector; both located on the

inside of the motor compartment at the

front of the treadmill.

BLUE BAG

STEP

Please refer to back cover for this

procedure, then return to Step 6.

AUTO-CALIBRATION

STEP

TV Power Cable

Coaxial Cable

TV BRACKET WIRING

1 2 3

Assembly 1

Comments to this Manuals

No comments

Vision Fitness T9800 Series User Manual Page 3

Comments to this Manuals

Related products and manuals for Treadmills Vision Fitness T9800 Series