Vision-fitness ST200 User Manual Page 1

AssemblyGuideST200FUNCTIONAL TRAINER

102STEP• Thread pull pins partially onto 2a (Qty. 1)and 2c (Qty. 2).• Lay the front center vertical (2f) on thefloor. Slide the seat support structure

113STEP• Place the top front structure (3a) on topof 2f and attach with two bolts(M10x1.5Px60L), two flat (10.5x18x2T)washers, and two nuts (M10x1.5P)

124STEP• Place the bottom of the left oval upright(4a) onto the protruding bolts of 1d.NOTE: Make sure the 27 holes of 4a areon the outside. Mate the

135STEP• If you are adding 15 weight plates to thebase unit, proceed as follows. If you areadding 20 weight plates, the steel tubespacer (5a) will not

146STEPWrap one end of cable #1 around pulleyA. On the right side of the unit, place itthrough pulleys B, C, D of 6a, and E.Remove the nuts from 2 slo

157STEPIf assembling just the base unit (ST200),proceed as follows. If assembling with theleg press (ST250), refer to Step 5 of theleg press assembly

168STEP• Remove the slotted bolts (8a) located onthe inside of the right and left handles ofuprights 4a & 4b. Remove the nuts fromthe bolts. Slide

179STEP• Place the rear hole of the left decorativecover (9a) over the threaded post on theleft side of structure 5e. Loosely attach aspring (SW10.2x1

18General Warning/SafetyDecal PlacementWeight Plate Sticker Placement10STEP• Attach the decals according to the diagram below.DECALS

19

2To avoid possible damage to this Functional Trainer, please follow these assembly steps in the correct order. Before proceeding, find your new Functi

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373www.visionfitness.com

32STEP1STEP3STEP4STEP5STEP6STEP7STEP8STEP9STEP

419mm Wrench6mm L-Shaped WrenchTOOLS & PARTS INCLUDEDPARTS BOXColor-coded Hardware BagsOwner’s GuideAssembly GuideWarranty Card10mm/17mm Wrench4mm

5ORANGE BAGBLUE BAGHARDWARE INCLUDEDSW10.2 x 18.4 x 2.5T Spring WasherQuantity: 410.5 x 18 x 2T Flat WasherQuantity: 8M10 x 1.5P NutQuantity: 6M10 x 1

6PINK BAGGREEN BAGHARDWARE INCLUDED10.5 x 18 x 2T Flat WasherQuantity: 2M10 x 1.5P NutQuantity: 2M10 x 1.5P x 60L BoltQuantity: 2M10 x 1.5P x 25L Bo

7BLACK BAGYELLOW BAGHARDWARE INCLUDED10.5 x 18 x 2T Flat WasherQuantity: 6M10 x 1.5P NutQuantity: 4M10 x 1.5P x 60L BoltQuantity: 2M6 x 1P x 50L Bol

8RED BAGHARDWARE INCLUDEDSW10.2 x 18.4 x 2.5T Spring WasherQuantity: 10M10 x 1.5P x 25L BoltQuantity: 10

91d1b1e1c1a1STEP• Lay the back side of the rear verticalupright (1a) down onto the floor. Thethreaded bolt ends will be pointing up.Place the center f